please help me to remove this error

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Title: please help me to remove this error
Thread Modes

fairbird Offline

magTrisaVE

Posts: 1,992
Threads: 181
Joined: Jan 2012
Reputation: 144

Thanks Given0

Thanks Received34

Thanks Meter 10%

#11

04-23-2012, 07:53 PM

Ok...If the third proposal also does not work..Put here the error that appears in the front border ..

morteza Offline

Junior Member

Posts: 11
Threads: 1
Joined: Apr 2012
Reputation: 0

Thanks Given0

Thanks Received0

Thanks Meter 0%

#12

04-23-2012, 08:00 PM (This post was last modified: 04-23-2012, 08:14 PM by morteza.)

the third part was sent with optiflasher no lan serial port

Power ON DB Device [ESC to Abort]
DM800HD Detected !
Dreambox Detected...Ok!
Sending Flash Loader...
Second Stage OK!
Boot Success & Ready For Job Process!
Name: Merlin-3-dm800-11-19-ramiMAHER.nfi
FSize: 42112288 bytes
Authorization id: 5DBA0418
Flashing IMAGE Phase1...
Finalizing Job Phase2...Please Wait...
Dreambox Flashed Successfully !

but after the reboot the box says error! in lcd

what a hell is wrong with this box?

fairbird Offline

magTrisaVE

Posts: 1,992
Threads: 181
Joined: Jan 2012
Reputation: 144

Thanks Given0

Thanks Received34

Thanks Meter 10%

#13

04-23-2012, 08:29 PM

I told you if does not succeed, Put exactly the error that appears in the front border ..

morteza Offline

Junior Member

Posts: 11
Threads: 1
Joined: Apr 2012
Reputation: 0

Thanks Given0

Thanks Received0

Thanks Meter 0%

#14

04-23-2012, 08:37 PM (This post was last modified: 04-23-2012, 08:38 PM by morteza.)

that is it
when the box comes on it shows Dream Multimedia
-> error!
and the red light keeps blinking

fairbird Offline

magTrisaVE

Posts: 1,992
Threads: 181
Joined: Jan 2012
Reputation: 144

Thanks Given0

Thanks Received34

Thanks Meter 10%

#15

04-23-2012, 09:03 PM (This post was last modified: 04-23-2012, 09:05 PM by fairbird.)

Ops....you never mentioned this error.
Cause of this problem if motherboard does not connected with sim card, maybe sim was Corrupted or not install in the right place...
It can be a difficult problem.
So the soultion:
My advice..
1. Make sure the simcard properly sits into the holder.
2. Check the contacts, clean it.
3. Or flash that image and you press the SIM Card.
probably the simcard is defective, replace or try to repair it with a card reader.

morteza Offline

Junior Member

Posts: 11
Threads: 1
Joined: Apr 2012
Reputation: 0

Thanks Given0

Thanks Received0

Thanks Meter 0%

#16

04-24-2012, 06:30 PM

HI
i dont think is the sim card with the other sim (original) i get the same error
i have a simcard reader (omnikey) the simcard dosent go in because the head of it is thick.
i think my problem is hardware problem when the box trys to boot it checks every part to come up,it looks like it stops on checking a faulty part and gives the error.

fairbird Offline

magTrisaVE

Posts: 1,992
Threads: 181
Joined: Jan 2012
Reputation: 144

Thanks Given0

Thanks Received34

Thanks Meter 10%

#17

04-24-2012, 06:44 PM (This post was last modified: 04-24-2012, 06:47 PM by fairbird.)

Here picture and some description from some friend..Thank you "Johnny-burrp"

Howto measure pin 1 (DC volt measurement).
And about original sim..How to put sim and how to flash image..Tell me how you did? put the sim first, or flash org. image?

Attached Files Thumbnail(s)

morteza Offline

Junior Member

Posts: 11
Threads: 1
Joined: Apr 2012
Reputation: 0

Thanks Given0

Thanks Received0

Thanks Meter 0%

#18

04-25-2012, 05:24 AM

HI
i put the sim in first then flash with original image

fairbird Offline

magTrisaVE

Posts: 1,992
Threads: 181
Joined: Jan 2012
Reputation: 144

Thanks Given0

Thanks Received34

Thanks Meter 10%

#19

04-25-2012, 12:10 PM (This post was last modified: 04-25-2012, 12:12 PM by fairbird.)

It was wrong way...
Do this steps:
1.Put old sim.
2.Use opiflasher.
2.Flash Last SSLxx for original image.
3.Unplug box.
4.Flash any new original image. I recommend you the first time this image
[Only registered and activated users can see links You are not allowed to view links. Register or Login to view.]
5.Unplug box.
6.Change sim to original.
7.Plug box again.
This is right way to change and replace sim.
If your box booting fine so congratulation. If not take your box to technical to make test and chack sim area and motherboard.

stigmata1823 Offline

Junior Member

Posts: 5
Threads: 1
Joined: May 2012
Reputation: 0

Thanks Given0

Thanks Received0

Thanks Meter 0%

#20

05-18-2012, 04:09 PM

im having the same problems here guys

Pages (3): « Previous 1 2 3 Next »

Thread closed

Possibly Related Threads...
Thread		Author	Replies	Views	Last Post
	OptiFlasher Error: socket Error # 10060!	enzo.57	2	27,904	01-01-2019, 08:51 PM Last Post: Stephenden

View a Printable Version

Forum Jump:

Browsing: 17 Guest(s)

About us

Navigation

Quick links

Login at www.yassinov.com

About us

Navigation

Quick links