05-15-2014, 10:00 PM
0
(05-15-2014, 06:33 PM)daroger Wrote: You are not allowed to view links. Register or Login to view.(05-15-2014, 02:01 PM)fairbird Wrote: You are not allowed to view links. Register or Login to view.First things you must be to do it... fix box (No Ca found) with null cable (rs232) only...You can not fix your box by lan cable...
So if you get problem to flash new image ..
-Try another null cable (Rs232)
-Try another Pc
Are you sure this fix should work with A8P sim?
After choosing LD2 loader, serial link I get:
--
Power ON DB Device [ESC to Abort]
DM800HD Detected !
Dreambox Detected...Ok!
Sending Flash Loader...
Second Stage OK!
Boot Success & Ready For Job Process!
I/O error 6
EInOutError
--
The dm800 display shows an ipaddres, so looks like if it was succesfull. After reboot same "no ca found"
And some additional info. When I connect with putty over serial I get:
----
© 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}
2ND STAGE OK, build #84 (2011-09-02)
0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
OLED found!
NO CONFIGURATION DATA PRESENT. STOP.
lcd: * ERR01: NO CA FOUND
----
So SSL looks good, SSL 84 reflash doesn't help.
When I press "x" the box boots.
--
13.932 - load config
13.960 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 285065
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright © 2006, Luc Saillard
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm800 (ghost@rabbit) (gcc version 4.4.3 (GCC) ) #1 Tue Mar 27 12:15:44 UTC 2012
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
1 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
--
Any clue how to fix the CA error?