[brate]

0

Hello @ all

I have for the first time now absolutely no idea what i can do anymore

I have a DM800se with SIM210
Sadly i "flashed" NN2 image with the latest DreamUP 1.3.3.11 and at the point flashing from its memory it wont go anymore further so i disconnected and shut down the box

and this is where the problem starts
now i can't flash anything anymore
SunrayFlashUP is connecting but stops at "upload completed waiting for acknowdledge" i cant flash any SSL or Image cause the flash image button is not showing up

Optiflasher i tried both baudrates and the flasher is Sending also flash loader but then nothing happens anymore

i also tried recover bad sectors but i guess i am not comming that far

i just want to 100% if this box is dead so i can forget it

thx in advance

this is the complete bootlog

Code:

BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000006
WC1=FFFFFFEE
RC2=00000015
WC2=00000039
RC3=0000000D
WC3=FFFFFFE6
RC4=0000000D
WC4=00000039
NWC=0000000F
RC5=00000006
WC5=0000000F
RC6=00000015
WC6=0000000F
NRC=0000000D
RW=00000010
WW=00000054
G=00000000 R=0000000D W=0000000F
BL=00000000
RC1=00000003
RC2=00000014

BL=00000001
RC1=00000009
RC2=00000015

BL=00000002
RC1=00000003
RC2=00000011

BL=00000003
RC1=00000003
RC2=00000012

BL=00000004
RC1=00000004
RC2=00000013

BL=00000005
RC1=00000007
RC2=00000014

BL=00000006
RC1=00000004
RC2=00000015

BL=00000007
RC1=00000006
RC2=00000018
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800SE

FIRST STAGE 1.0/400 {B

[brate]

0

If your box is out of warranty then please confirm first that your sim is 2.10
by opening the box & read the label writen on sim & try to remove it & put it back .
After that try to use Repair No ca Found from OptiFlasher using Advanced Mode 2
then post the log of your operation

Yes no warranty anymore sadly
i am 100% sure it's 2.10 the box is completly opened i removed the tuner and HDD to try flash but it does not help
i cleaned the SIM and the pins with Isoproply

i tried your advise but it ends with the same result
Sending flash loader...until 100% ( it goes fast)

then nothing happens

[brate]

0

DreamUp V1.3.3.11 have no patched version for clone so from the begin
is a mistake using this !
Is your problem appear only after flashing NewEnigma2 image that caused this problem ?

exactly

my dm worked fine on NN2 3.3.2 but i wanted to update
i took original dreamup flashed NN2 4.0.5 lean by rami maher
and now box wont boot at all

i think my box is seriously broken -.-

maybe first bootloader is broken if thats possible

[blowagie]

0

Hi,

I do have exact the same problem. Did you manage to resolve this problem?

I can't flash a second time, I then get wrong boot response. If I wait more yhan 15 minute, I can flash with the same result: Sending flash loader .....

I already tried another sim2.10, same problem.

Tx

Bart

Log after second time power on (via putty com4):

BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000004
WC1=00000010
RC2=00000017
WC2=00000034
RC3=0000000D
WC3=FFFFFFE2
RC4=0000000D
WC4=00000035
NWC=0000000B
RC5=00000005
WC5=0000000B
RC6=00000017
WC6=0000000B
NRC=0000000E
RW=00000013
WW=00000054
G=00000000 R=0000000E W=0000000B
BL=00000000
RC1=00000003
RC2=00000014

BL=00000001
RC1=00000004
RC2=00000014

BL=00000002
RC1=00000004
RC2=00000013

BL=00000003
RC1=00000005
RC2=00000014

BL=00000004
RC1=00000005
RC2=00000014

BL=00000005
RC1=00000005
RC2=00000016

BL=00000006
RC1=00000004
RC2=00000014

BL=00000007
RC1=00000006
RC2=00000016
3
COPY CODE
COMPARE CODE