[elam777]

0

Dreambox NCF Repair Tool SIM2 Edition v2.0 By YASSINOV
Power ON DB Device [ESC to Abort]
Operation Start at: 11:54:35
DM800HD Detected !
Dreambox Detected...Ok!
Sending Flash Loader...
Second Stage OK!
Boot Success & Ready For Job Process!
Authorization id: 9C80AE08
Starting Repair [NO CA FOUND] Injecting Phase1...
Finalizing Job Phase2...Please Wait...
NO CA FOUND Repaired Successfully !
Operation Done at: 11:55:58
..................................
But when I rebooted my DB again,
New message on the display of my DB:
SIM201 team # 84B error,
[Only registered and activated users can see links You are not allowed to view links. Register or Login to view.]
error 01: NO CA FOUND
..............
Please help me
Thank you

[fairbird]

0

Please put full details for your box..
what kind of sim you have simFerrari, sim1 or sim201 ?
and please put here output hyper see here how to..
[Only registered and activated users can see links You are not allowed to view links. Register or Login to view.]
P.s: if you do not know your sim..open screws from your box and remove cover then see your sim beside tuner.

[elam777]

0

Hello,
DM800 HD PVR, and I think it is a clone.
I dont know much about the sim card, but it's like a mobile sim card, white colors and this nr:
WT10
2932

---

Hello,
Here are result of hyper:
© 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #75 (20091005)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000123,00000133}
0.007 - fp init
0.008 - ca init
SW != 9000
error in receive
error during t1 transfer
cannot read cert(1)
SW != 9000
error in receive
error during t1 transfer
cannot read cert(1)
SW != 9000
error in receive
error during t1 transfer
cannot read cert(1)
SW != 9000
error in receive
error during t1 transfer
cannot read cert(1)
SW != 9000
error in receive
error during t1 transfer
cannot read cert(1)
CA invalid
OLED found!
NO CONFIGURATION DATA PRESENT. STOP.
* ERR01: NO CA FOUND

[fairbird]

0

I think your sim is sim1 T3 and you can not use bootloader for sim201..only you can use image with bootloader 69 old image..
So try to reflash your box with SSl69 in attach and use optiflasger "Flashing by Null modem cable only without Network lan" method..
[Only registered and activated users can see links You are not allowed to view links. Register or Login to view.]

But i think your box will not boot because you flashed wrong image with high version of your sim..So if you not boot after flash SSl69, Again flash your box with right image with image include ssl69..

Let us know if you solved..

[elam777]

0

Hello again.
I've done what you said.
but have downloaded the program (Gemini 5.0-OE1.6-DM800-SSL69_TSv2.nfi) and flashed my dreambox. It went well and my dreambox flashed completely in step 1
but in step two can not flash with the network! nor can not flash with the network as well. what can I do now?
Now that I restarted my dream box it comes booting, and then, now stands on the screen and bytes between the words!: DVI, SCART, YPbPr.
thank you for your help

[fairbird]

0

You have solved your problem..it's ok
About network , if you press and holding press on power button and you get ip and you can not flash with network, so check another internet wire..

In this case if you solved your problem i will close thread under solved..