+- InfoServ (https://www.yassinov.com/forum)
+-- Forum: Satellite Equipment (https://www.yassinov.com/forum/forumdisplay.php?fid=9)
+--- Forum: Dreambox NO CA FOUND Repair Tool (https://www.yassinov.com/forum/forumdisplay.php?fid=40)
+--- Thread: [SOLVED] NCF Repair Tool stucks on Job Phase 2 (/showthread.php?tid=908)
NCF Repair Tool stucks on Job Phase 2 - tumakha - 06-17-2012
-DM800se
-Clone
-SIM2.10
-No Ca Found After Flash image
I tried with the NCF 2.5, any ssl, but none of them brings me to the end of the process...
The software detects the receiver, all works ok, but it stucks on:
Finalizing Job Phase 2... Please Wait....
And I get message on Dreambox display:
Webinterface -
Couldn't listen on:
192.168.1.77:443
Hyperterm dump:
4567
© 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800SE
FIRST STAGE 1.0/400 {BO23456}
2ND STAGE OK, build #84 (2011-09-01)
0.000 - BCM board setup
0.000 - fp init
0.000 - ca init
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
CA invalid
OLED found!
color oled reset
NO CONFIGURATION DATA PRESENT. STOP.
lcd: * ERR01: NO CA FOUND
0.861 oled: string too long: '* ERR01: NO CA FOUND'
RE: NCF Repair Tool stucks on Job Phase 2 - tumakha - 06-17-2012
Lan cable was also connected.
But is not enough usb cable for repair?
I need put some "Authorization id:" ?
RE: NCF Repair Tool stucks on Job Phase 2 - fairbird - 06-18-2012
Look try with Optiflasher..
Flash to your box SSl84 (bootloader) by optiflasher with cable only without network..and let us know
See here.. and use "Flashing by Null modem cable only without Network lan" method..
RE: NCF Repair Tool stucks on Job Phase 2 - tumakha - 06-22-2012
1. I get error 'Invalid filename' if I use option - Repair [NO CA FOUND].
Screenshot attached.
2. I try option flash image but it not take effect.
Power ON DB Device [ESC to Abort]
DM800HD SE Detected !
Dreambox Detected...Ok!
Sending Flash Loader...
Second Stage OK!
Boot Success & Ready For Job Process!
Name: release-dm800se-3.1.0.nfi
FSize: 42855712 bytes
Then I can flash image by web browser, but after reboot dreambox again without IP and "ERR1: NO CA Found" on display.
RE: NCF Repair Tool stucks on Job Phase 2 - fairbird - 06-22-2012
I have never said to use Repair [NO CA FOUND]...
Please read me post carefully..
1-open optiflasher.
2-Detect your com.
3-Select Write bootloader
4-Click Do job and flash SSl..
5-If not boot your box make again and select write image and flash any image with SSl.
RE: NCF Repair Tool stucks on Job Phase 2 - tumakha - 06-23-2012
I use this image
I try with newnigma2-release-dm800se-v3.3.2.nfi and secondstage-dm800se-84.nfi.
Could you give link to right image with SSl?
RE: NCF Repair Tool stucks on Job Phase 2 - tumakha - 06-23-2012
I try with newnigma2-dm800se-v3-3-2-ramiMAHER.nfi, Nemesis2-6-dm800se-SVN-108r4-ramiMAHER.nfi and OpenPLi-3.0-beta-dm800se-20120623.nfi.
Same result.
Final screenshot attached. Maybe not finalized flashing?
RE: NCF Repair Tool stucks on Job Phase 2 - tumakha - 06-23-2012
Fixed by FerrariFiller_1_3_3_7FSE.exe