+- InfoServ (https://www.yassinov.com/forum)
+-- Forum: Satellite Equipment (https://www.yassinov.com/forum/forumdisplay.php?fid=9)
+--- Forum: Dreambox OptiFlasher Pro [DMips EDition] (https://www.yassinov.com/forum/forumdisplay.php?fid=69)
+--- Thread: [SOLVED] DM900 4K wont go to rescue mode (/showthread.php?tid=4665)
DM900 4K wont go to rescue mode - Hannibal - 11-11-2017
Hi Team,
Please can you help to recover my box DM900 which got stuck after flash trial through web browser mode, the image tried was "openpli-5-dm900-20170607.rootfs.tar" after thatv the box just show a nice picture then the green screen comes up saying software issue and will reboot, but it stays an the green screen for ever. please help.
With Putty I got this:
CPU 01
Dreambox DM900
AVS init...
AVS init OK
AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2 a002b00
AVS load_code offset =00051000
LOADED
AVS: overtemp mon ON
single board
select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
MEMSYS-STD
SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
MCB: FLEX
AVS start:status=000000ff
STB: Current voltage=0000036c(876)
temperature=0000e253(57939)
PV=00000334(820)
MV=0000036c(876)
AVS FW rev=30333278 [0.3.2.x]
OK
DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
Sdram Scramble OTP = 0x00000001
Sdram Scramble OK
select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
BFW load mode OTP = 0x0000000f
bfw_hash_locked = 0x00000000
BFW key3 OK, BFW load OK
BFW v2.1.0
COPY CODE... DONE
MICH: disable success
SSBL
PINMUX
CACHE FLUSH OK
MMU ON
CACHE FLUSH OK
_fbss 07080cd0
_ebss 0713dd70
_end 0713dd90
HEAP @ 07200000
STACK @ 09300000
ARCH: CONFIG OK
CLR BSS 07080cd0 to 0713dd70 OK
CLR SRAM OK
CACHE FLUSH OK
CPU CLKSET OK
GO!
,/
,'/___, BOLT v1.18 v1.18 LOCAL BUILD
.'__ ,' (2016-12-01 16:24:31 cynric@cynric-VirtualBox)
/,' Copyright © 2016 Broadcom
/'
Board: BCM97252SSFF
SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovi sion_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
CPU: 2x B15 [420f00f3] 1719 MHz
SCB: 432 MHz
DDR0 @ 1067MHz, DDR1 @ 1067MHz
RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
CS1: NAND: unrecognized ID: 0x20ffff 0xffffffff
RTS0: 0x1101004, 256 clients, ok
RTS1: 0x1181004, 256 clients, ok
BOX MODE: 5
card if inited
set pwm to 0/255
disp id 5420
load image
AVS: park check
AVS: temperature monitoring enabled
AVS: STB: V=0.875V, T=+59.400C, PV=0.820V, MV=0.876V, FW=30333278 [0.3.2.x]
USB otp=00000040
USB @ 0xf0470200: IPP is active low, IOC is negative polarity
init fp
found card in unknown state
ca valid!
set pwm to 200/255
Normal bootup
Loader:zimg Filesys:raw Dev:emmcflash0.kernel File: Options:(null)
Reading 11648176 bytes from zImage...........
Starting program at 0x8000 (DTB @ 0x7728000)
32 bit boot...
Uncompressing Linux...Uncompressing Linux...
CPU exception: ABT
r0 : 0000c4e4
r1 : 00000060
r2 : 00b23c80
r3 : 00000060
r4 : 00b23c80
r5 : f80000fe
r6 : ffffffff
r7 : 00000000
r8 : 00010000
r9 : 00010000
r10 : 00000030
r11 : 00b23ca8
r12 : 00000001
r13 (sp): 00b24c90
r14 (lr): ffdfa62c
r15 (pc): ffdfa624
cpsr : 600001d3
dfsr : 00000000
dfar : 00000000
ifar : ffdfa628
DM900 4K wont go to rescue mode - Warnerfed - 12-30-2018
Hi
You need to use OptiFlasher Pro Ultimate on Advanced Mode with the following settings :
-Connect Network