+- InfoServ (https://www.yassinov.com/forum)
+-- Forum: Satellite Equipment (https://www.yassinov.com/forum/forumdisplay.php?fid=9)
+--- Forum: Dreambox OptiFlasher Pro [Basic EDition] (https://www.yassinov.com/forum/forumdisplay.php?fid=35)
+--- Thread: clone dm800hd cant flash new image stuck on 1% (/showthread.php?tid=4609)
clone dm800hd cant flash new image stuck on 1% - icepopa - 09-07-2017
hi guys need help big time with dm800hd
i flash an image and its never been the same. i think i flashed a corrupt image now all i get i 1%
when trying to flash new image.
i think my second boot stage config file is corrupt.
i tried to fix with optiflasher
i tried no ca found fix
i tried bootloader fix/update
i tried dreamup too
i tried with ethernet and usb serial cable
i can boot up to first stage and see the lcd screen on my box
1 can see ip address 192.168.1.10 with sim201 #84b lcd: *** STOP ***
but wont go any further until new image is on
i still only get 1% when trying to flash new image via browser or dreamup both clone and normal version
or optiflasher 3.0.
on my browser it uploads image 100% but
i get "Writing to flash memory, please do not turn off power!" but stuck on 1%
i got a log file save of whats going on in my box can someone help?
box dm800hd clone
sim 201
boot loader 84b
The Log file
ðÿü
© 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D
FIRST STAGE 1.00 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-02)
0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
1.117 - load config
dCA: not existent, loading defaults
1.148 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84B
- read config file: /boot/secondstage.conf
detected old jffs2 sig.. disable hw ecc
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . | / - \ | / - \ done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/bootlogo-dm800.elf.gz
bootlogo size: 78479
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright © 2006, Luc Saillard
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-2.6.18-7.4-dm800.gz
executing '/boot/vmlinux-2.6.18-7.4-dm800.gz' returned: -2
waiting for link...
link timeout.
lcd: /boot/zImage.elf
find_inode failed for name=zImage.elf
load: Failed to find inode
no valid boot source found. press any key to enter setup.
lcd: *** STOP ***
if anyone know how to fix this issues it would be well appreciated.
