The following warnings occurred: | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Warning [2] Undefined array key "isclosed" - Line: 203 - File: inc/plugins/guestwarn.php PHP 8.2.26 (Linux)
|
No Ca Found - Printable Version +- InfoServ (https://www.yassinov.com/forum) +-- Forum: Satellite Equipment (https://www.yassinov.com/forum/forumdisplay.php?fid=9) +--- Forum: Dreambox NO CA FOUND Repair Tool (https://www.yassinov.com/forum/forumdisplay.php?fid=40) +--- Thread: No Ca Found (/showthread.php?tid=2544) |
No Ca Found - brianmullen8 - 03-31-2014 I have been trying to connect this dm800 with sim 2.10 to dreamup all day but could not get a connection. I used hyperterminal but could not get a good read out with baud rates at 115200 or 57600 but it will read normally at 38400. Is it possible to flash using hyperterminal or change the baud rate on the dm800? The no CA tool uses 115200 or 57600. Dreamup uses 115200. I also tried an old sim 2.0 but with the same results Any other ideas for this. Thanks RE: No Ca Found - fairbird - 03-31-2014 Read these topics and and also this RE: No Ca Found - brianmullen8 - 03-31-2014 Thanks for the reply. I have read through all them posts but nothing helpful. I have fixed a dm800 with no ca found error on another box with optiflasher and had no problems. I have tried 3 null modem cables. I think the problem is the baud rate. I connected my dm500 up to dreamup and it connected ok at 115200. No ca tool does not detect the box when powered. Thanks RE: No Ca Found - fairbird - 03-31-2014 Try another Pc... Make sure Firewall and anti virus tools not block optiflasher RE: No Ca Found - brianmullen8 - 04-01-2014 Hi I have disabled firewall and antivirus, tried a laptop still the same. Thanks RE: No Ca Found - pisces - 04-03-2014 hi.. i had same issues while i was trying to fix my problem and i fixed every thing with windows XP Pro it hasn't worked for me with windows vista , 7 , 8 and 8.1. Not sure if its gonna help you but you can give a try. Good Luck RE: No Ca Found - brianmullen8 - 04-10-2014 (04-03-2014, 12:57 AM)pisces Wrote: You are not allowed to view links. Register or Login to view.hi.. Just tried a fresh install of windows xp still the same. Hyper terminal will only communicate properly at 34800. all the tools to fix it need to be @ 57600 or 115200 is there anyway to change the baudrate in dream up, I looked in hex edit but I can't see anything that stands out. Thanks RE: No Ca Found - brianmullen8 - 04-13-2014 Here is a print out at 38400 baud rate, The first one is a sim 2.10 the second is a sim 2. I was going to buy another sim but i still wont be able to flash. i think the baudrate has been set to 38400 at some point by someone. can i reset the bios on dm800? © 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM800 FIRST STAGE 1.00 {BO23456} 2ND STAGE OK, build #76 (20100419) 0.000 - BCM board setup {00000126,00000126,00000125,00000124,00000123,00000133} 0.007 - fp init 0.008 - ca init cannot read cert(2) cannot read cert(2) cannot read cert(2) cannot read cert(2) cannot read cert(2) CA invalid OLED found! NO CONFIGURATION DATA PRESENT. STOP. * ERR01: NO CA FOUND © 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM800 FIRST STAGE 1.00 {BO23456} 2ND STAGE OK, build #76 (20100419) 0.000 - BCM board setup {00000126,00000126,00000125,00000124,00000123,00000133} 0.007 - fp init 0.008 - ca init CA invalid OLED found! NO CONFIGURATION DATA PRESENT. STOP. * ERR01: NO CA FOUND RE: No Ca Found - fairbird - 04-13-2014 Your problem no from sim not from software ...From connection 1-Try another pc (win xp better) 2-Try another Rs232 cable RE: No Ca Found - brianmullen8 - 04-13-2014 (04-13-2014, 05:42 PM)fairbird Wrote: You are not allowed to view links. Register or Login to view.Your problem no from sim not from software ...From connection I have tried from 2 pc's windows 7 and fresh install of windows xp and 1 laptop with windows 8 i have tried onboard com port and usb com port *****I just had it on putty and when i right clicked on putty screen it went to serial connection mode on the display and in putty it said serial loop mode. but i couldn't do anything. Dreamup said file too big and wont connect i tried to press s for setup but nothing. I switched the dm800 off and on a few times and each time i could get it to go to serial connection by right clicking on putty screen. I went onto xp hoping hyperterminal would let me press s but now i cant get it to serial mode.***** Update, In putty again and i just frantically started pressing buttons on the keyboard and it has started booting but it is stuck. im going to try 1 key at a time until i find out whats going on. © 2007,2008 Dream Multimedia GmbH. All rights reserved. Dreambox DM800 FIRST STAGE 1.00 {BO23456} 2ND STAGE OK, build #76 (20100419) 0.000 - BCM board setup {00000126,00000126,00000125,00000124,00000123,00000133} 0.007 - fp init 0.008 - ca init CA invalid OLED found! NO CONFIGURATION DATA PRESENT. STOP. * ERR01: NO CA FOUND 6.193 - load config dCA: not existent, loading defaults 6.224 - config loaded. * press [S] to enter setup OLED found! BOOT #76(20100419) detected jffs2 blocksize: 16kb +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ++++++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU dreamupd initialized Scanning JFFS2 FS: . done. /flash/bootlogo.elf bootlogo size: 195531 using 1280x720p (60.00 Hz) Using the Small jpeg decoder library, Copyright © 2006, Luc Saillard <luc@saillard.org> parsing JPEG header.. JPEG Size: 1280x720 /flash/vmlinux.gz <5>Linux version 2.6.18-7.3-dm800 (tux@debian) (gcc version 4.4.3 (GCC) ) #1 Wed Jul 21 17:43:45 CEST 2010 Fetching vars from bootloader... none present, using defaults. board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2 Detected 256 MB on board <4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824 Default command line = root=/dev/mtdblock3 rootfstype=jffs2 rw console=null 1 831ffed8 8303c848 g_board_RAM_size=256MB Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0 CPU revision is: 00020000 Determined physical RAM map: memory: 10000000 @ 00000000 (usable) ---> memsize from bootloader: 148 User-defined physical RAM map: node [00000000, 09400000: RAM] node [09400000, 06c00000: RSVD] <5>Reserving 108 MB upper memory starting at 09400000 <7>On node 0 totalpages: 65536 <7> DMA zone: 65536 pages, LIFO batch:15 Built 1 zonelists. Total pages: 65536 <5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null before init RAC 0x02a00000 0x00000000 after init RAC 0x02a0000f 0x0fff0000 |